Adblueobd Adblueobd2 for Volvo Euro6 , Avoid all ofAdblueobd system errors, and do not get andAdblueobd or NOx fault, Prevent torque loss

AdblueobdAdblueobd2for Volvo Euro6

Top 4 Reasons To GetAdblueobdAdblueobd2for Volvo Euro6:

Avoid all ofAdblueobdsystem errors

Do not get andAdblueobdor NOx fault

Prevent torque loss

Importance ofAdblueobdAdblueobd2for Volvo Euro6 :

Trucks generally giveAdblueobdor nox system errors so work hard. Your truck can cause loss so someAdblueobderrors or fault lights.

These problems cause you money and time. After installingAdblueobdremoveAdblueobd2, you dont get otherAdblueobderrors and you do not need to addAdblueobdfuel. After the installation, yourAdblueobdfuel level will be up automatically.

AdblueobdRemoveAdblueobd2disable these systems:

AdxBlue system (All)

AdxBlue NOX sensor

DPF system

DPF temperature sensors

DPF regeneration Supported Models:

Euro 6 for the Volvo FMX Series

Euro 6 for the Volvo FH Series

Euro 6 for the Volvo FM Series

nitro group adBlueOBD2 for Daf Euro 6 460 480 Remove

You must attach the adBlueOBD2 to the rear of the silencer under the EASecu.

You must first disconnect the nox sensor cables and connect the adBlueOBD2 cables to theNOxcables.

you must obtain fuseoF22 (e497 15A)

CAN cables are located at the top of the NOx socket.

Carsidemutator side

CAN H-----------------------WHITE cable

CAN L------------------------ BROWN cable

POWER(+)--------------------REDcable

GND(-)------------------------ Black cable

IMPORTANT NOTE:Only the CANcables are to be connected from the NOx socket as the truck’sfuse has been taken.For power connections you need to use ground (GND) and contact(+).

Youmust clear the error codes from the engine ECU, If you do not have DAVIE software, you canus DAFEuro 6 DTC Eraser.

The connection type DAF460/480 is the same but the NOx socket locations are different. Thefollowing are shown.

AdblueOBD2 AdblueOBD2for Scania Euro6,

not need to be leaming, you have to mountAdblueOBD2in the plug of the EEC(AdblueOBD2)ECU(in the pink one),Yon can find EEC ecu ta the center of the vehicle frame.Two big plugs(one is pink) in this manual you will find pin mumber of the EEC plug,also colours cables of EEC andAdblueOBD2.

AdblueOBD2AdblueOBD2for Scania Euro6:

AdblueOBD2for Scania Euro 6 not need to be leaming

You have to mountAdblueOBD2in the plug of the EEC(AdblueOBD2)ECU(in the pink one),Yon can find EEC ecu ta the center of the vehicle frame.Two big plugs(one is pink)

in this manual you will find pin mumber of the EEC plug,also colours cables of EEC andAdblueOBD2.

Connect wires of theAdblueOBD2with this table as reference:

Red(Vcc)-PIN 12 (green) Cut the cable after connectAdblueOBD2to truck side

Black (GND)-PIN 4 (fat black)

Yellow (CAN H）-PIN 22（orange)

Green (CAN l)-PIN 19 (fat black)

Package List:

1pc xAdblueOBD2AdblueOBD2for Scania Euro6

EURO6adblueobd2 adblueobd forIVECO Installation

IVECO Stralis

adblueobd2adblueobdfor iveco Euro 6 not need to be learned.We fitadblueobdunder the cover ofadblueobd2tank (behind of right front wheeL)

SCR system in Iveco Euro 6 is not typical. All aftertreatment process is managed by engine ECUEDC17Cv41 there is no additonaladblueobd2ECU system. So some of the components connecteddirecly to engine ECU should be electrycally operating property, (adblueobd2injector, directionalValle, temperature sensors）

adblueobdreplaces the work：

Nox Sensor(downstream）

Nox Sensor(upstream)

NH3 Sensor

CAN wires we need connect separetly

The best place for it is plug ST55A (you can find it on the vehicle frame, right side of engine,above the right front wheel)

WHITE- to pin 22 (CAN H)

BROWN-to pin 21(CAN L)

Now only we need connect power (adblueobds red cable as VCC and black cable as GND)toignition power.Just remove the fuse NUMBER 70405 from 4th block.

ForIveco Eurocargo

adblueobdVehicle side

WHITE (CAN H)---------------- NoX Socket 4 pin

BROWN (CAN L)---------------NoX Socket 3 pin

Red (positive +)----------------adblueobd2socket 9 pin (7542)-(or ignition contact Line)

Black(GND-)--------------------adblueobd2socket 8 pin(o549)-(or chassis to print)

Remove the fuse number 3(15A)at block 70000/2 from the fuse box. Erase any errors.

nitro group adBlueOBD2 for MB Atego Euro 6 Remove adBlueOBD

Behind fuses in the middle is a plug- as in the price (not right like in manual-correct is middle)
Connnection colors-White with Blue (Truck side) with White (Truck side)

Red wire from emulator connection with any(+)after ignition

Black i GND

Next step is remove Fuse

F23 Thats all

You must locate the ACm Module and remove the socket.
The cable should be installed as shown in the picture below.
adBlueOBD2 White cable(CAN H) -----Atego vehicle socket 10 pin(CAN H)
adBlueOBD2 Brown cable (CAN L) ----- Atego vehicle socket 20 pin (CAN L)
adBlueOBD2 Red (+) -----Atego vehicle Positive(+)Cable
adBlueOBD2 Black(-) -----Atego vehicle GND (-)

After installation, you must remove errors with fault detecting device.
The DTC fault code eraser can also be used to erase the fault in your Atego vehicle

You will not mount the socket back into the ACM module Isolate the Atego ACh nodule without damage.